By Perth Honed Concrete · Planning guidance
The short version
- What it is: concrete with the thin top layer of cement paste removed so the decorative stone in the mix shows through. The result is textured and naturally slip-resistant before any sealer goes on.
- Where it suits Perth homes: driveways, paths, pool surrounds and alfresco areas — anywhere you want grip and a bit of character.
- The main trade-offs: texture depends on stone size, it can get slippery once a glossy sealer is applied, and it needs periodic resealing to stay looking its best.
- Two different readers: some of you are choosing a finish for a new project; others already have exposed aggregate that has gone rough or started losing stones. Both are covered below.
- Already have a rough or stone-shedding surface? Jump to whether it can be smoothed instead of replaced.
What is exposed aggregate concrete?
Exposed aggregate concrete is ordinary concrete with a decorative twist. In a plain slab, the stones (the aggregate) are hidden under a smooth skin of cement paste. With an exposed aggregate finish, that top skin is removed while the slab is young, revealing the stones packed just beneath it.
The appeal is twofold. First, the look: the colour and texture come from natural stone, so you get depth and variation a flat grey slab can't match. Second, the grip: a textured, stony surface is naturally slip-resistant before sealing, which is why it has long been a default for outdoor areas in Perth — driveways, front paths, patios and around pools.
It is very much an outdoor-and-high-traffic finish. If you want a sleek, smooth concrete look for an interior or a refined outdoor space, that is a different family of finishes — see exposed aggregate concrete and its honed and polished relatives rather than assuming one finish does everything.

How the stone gets exposed (the four methods)
How the stone is revealed changes both the look and how the surface wears. There are four common approaches.
Surface retarder, or chemical wash: A surface retarder (sometimes called a deactivator) is sprayed onto the fresh concrete. It chemically slows the set of the surface mortar while the slab below hardens normally. Once the slab underneath is firm, the softened top skin is washed off to reveal the stone.
Timing is everything, and it shifts with conditions — Perth's heat can bring the wash window forward, cooler days push it back. Rather than relying on a fixed number of hours, a careful installer uses a test panel to judge when to wash. The manufacturer's current instructions for the specific product should set the timing.
Wash, brush and water: Here the cement skin is removed mechanically while the concrete is still workable — typically a hose and a stiff broom, or a pressure washer — stripping the top few millimetres to expose the stone. Again, timing is critical: too early and you dislodge the stone, too late and it becomes hard work to cut back.
Seeding, or surface dressing: Instead of revealing stone from within the mix, decorative stone is scattered onto the fresh surface and worked in. This is useful for small areas and feature bands where you want a specific stone. The catch worth knowing: seeded stone sits in a relatively shallow layer, so it can be more prone to loosening over time than stone blended through the whole mix.
Grinding or honing: The surface can also be revealed — or softened later — by mechanically grinding the cured concrete. Grinding cuts coarser than a fine polish and is the route used to take the edge off a rough existing surface. This is the bridge to one of the most common questions we get, covered further down.
A note on any grinding work: concrete contains crystalline silica, so cutting and grinding has to be managed with a proper site control plan and project-specific work methods. Be wary of anyone describing grinding as a clean, hazard-free process — the dust is a genuine safety matter that a professional manages, not ignores.
Exposed vs washed vs seeded vs honed aggregate
These terms get thrown around as if they're interchangeable. They're not, and knowing the difference helps you compare quotes properly.
In short: washed aggregate and exposed aggregate sit in the same family and the words are often used loosely, while honed aggregate is a distinctly smoother, ground-back finish. If an installer's quote simply says "aggregate", ask which of these they mean — the preparation, the look and the wear are all different.
- Exposed aggregate: Top cement skin removed to reveal stone within the mix; Textured, stony, grippy; Driveways, paths, outdoor areas
- Washed aggregate: The same idea, where the skin is revealed using water/chemical wash of the slab's own top-layer stone; Very similar to exposed; terms overlap heavily; Outdoor areas; often used synonymously
- Seeded / surface-dressed: Stone placed onto the fresh surface rather than revealed from within; Controlled stone choice, but a shallower stone layer; Small areas, feature bands
- Honed aggregate: Cured surface ground down to a flatter, smoother cut; Smoother and flatter than exposed, still slip-rated for outdoors; A refined look, or softening a rough surface
Is it too rough or slippery? Texture, bare feet and wet weather
Two worries come up again and again: "will it be too rough?" and "will it be slippery?" They pull in opposite directions, and the honest answer is that both depend on choices made at the design stage.
Stone size and feel underfoot: The size of the stone is the main lever for how a surface feels. Smaller stones give a finer, gentler texture that's kinder to bare feet — worth thinking about for pool surrounds and alfresco areas where people walk barefoot. Larger pebbles read bolder from the street and suit a driveway, but can feel coarse underfoot.
There's no single "right" stone. It's a trade-off between appearance and comfort, and it's exactly the kind of thing to settle by looking at representative samples before the pour.
Slip when wet, and the sealer trade-off: Unsealed exposed aggregate is naturally textured, which is part of why it's used outdoors. The complication comes with sealing. A high-gloss or wet-look sealer can make a surface slippery when wet — more so on a slope or a pool edge. The standard answer is an anti-slip additive mixed into the sealer, which restores grip without giving up the finish you want.
So the sealer decision isn't just about looks. If the area gets wet and is walked on, raise anti-slip with your installer up front rather than discovering the problem after the first rain.
Rough, dated or losing stones? Can it be smoothed instead of replaced?
This is the question that brings a lot of Perth owners to us: my exposed aggregate is too rough, or it's shedding stones and looking tired — do I have to replace it?
Often, no.
Why stones come loose: Stones work loose for a few reasons: ordinary wear and heavy loads over the years, water sitting on the surface, or — commonly — finishing and timing at the time it was laid. If the surface was washed too early or exposed too deep, the stone was never well anchored to begin with. It's worth knowing there's no reliable DIY resin that re-binds loose pebbles into an existing surface, so patch-it-yourself fixes tend to disappoint.
The honing and resurfacing route: Because the surface can be mechanically ground, a rough or uneven exposed aggregate finish can often be honed back to something smoother and more even — taking the sharp edge off the texture and giving a tired slab a cleaner, more considered look. The result is closer to a honed aggregate finish: flatter, gentler underfoot, still suitable outdoors. Where the surface is sound but simply dated or inconsistent, resurfacing is another avenue worth assessing.
When replacing is the honest answer: Honing isn't a cure for everything. Where there's major cracking, movement or a level problem, grinding won't fix the underlying issue, and the honest recommendation may be to repair what's fixable or, in the worst cases, remove and re-lay. The only way to know which camp your slab falls into is a proper on-site assessment — anyone promising an outcome without seeing the slab is guessing.
Sealing, cleaning and maintenance in Perth's climate
Exposed aggregate isn't high-maintenance, but it isn't fit-and-forget either. A little care keeps it looking the way it did on day one.
Resealing: Sealing protects the surface, helps resist staining and lifts the colour of the stone. It also wears, which is why resealing is part of owning the finish. As a general guide from the wider trade, thin topical sealers (such as acrylics) need refreshing more often than penetrating sealers that soak in — but the right product and interval depend on your sealer, your traffic and your exposure, so follow the specific product's current guidance rather than a rule of thumb.
Perth's strong sun and heat matter here: UV and temperature are hard on sealers, so an outdoor surface in full WA sun will generally want attention sooner than one in shade.
One myth worth clearing up: you may read that exposed aggregate "doesn't need sealing" at all. That's an outlier claim and it runs against standard Australian trade practice. Most exposed aggregate benefits from periodic resealing to stay protected and looking good — see concrete sealing for how that's approached.
Cleaning and stains: Because the surface is textured and the cement skin is gone, exposed aggregate is a little more susceptible to oil and fluid staining than a sealed plain slab, and standing water can pit it over time. Clean up spills promptly, keep drainage working so water doesn't pool, and go easy with pressure washing — too aggressive and you can dislodge stone or strip sealer. Around pools, mineral deposits and efflorescence can be dealt with using an appropriate cleaner, followed by resealing.
Protecting colour: For coloured or oxide mixes, the concern is fade. Proper curing and sealing help protect the colour and keep it even. As with everything here, the specifics depend on the products used, so confirm the approach with your installer.
Will it suit your site? Perth soils and climate
Where you are in the Perth metro area genuinely affects a concrete project. Much of the city sits on free-draining Spearwood and Bassendean sands, which tend to make for straightforward driveway and slab work. That advantage fades on the clay pockets through the outer suburbs, on coastal dune sand, and up in the Perth Hills, where base preparation and drainage need more thought.
Climate plays in too. Perth's heat affects placement — on a hot day the exposure wash window can arrive faster, which is one more reason timing is judged on site rather than by the clock — and, as noted above, UV and heat drive how often you'll reseal. None of this rules exposed aggregate in or out; it just means the groundwork and product choices should suit your block, which is what a site assessment is for.
Exposed aggregate vs other Perth outdoor finishes
Exposed aggregate is one of several decorative concrete options WA owners weigh up. Here's an honest comparison.
There's no universal winner. If you love the natural-stone look and want grip, exposed aggregate is hard to beat. If you want something smoother and more restrained — or your existing exposed aggregate is too rough — honed concrete is the obvious sibling to look at. Liquid limestone is a genuinely different material that some owners prefer around pools. The best choice is the one that suits your space, your light and how the area will be used.
- Exposed aggregate: Stony, natural, varied; Textured, grippy; Great outdoors; can be rough underfoot depending on stone; needs resealing
- Honed concrete: Smoother, more refined; Flatter, still slip-rated for outdoors; A gentler feel; good where exposed aggregate would be too coarse
- Liquid limestone: Paler, masonry-like; Textured, cool underfoot; A common WA pool-surround choice; a different material and look
- Plain / broom finish: Simple grey; Broom texture; The budget baseline; least decorative, least grippy of the decorative options
What it costs in Perth — and how to compare quotes
We don't publish dollar figures, and we'd be cautious of anyone who hands you a firm per-square-metre rate before seeing your site. No verified business pricing is set out here on purpose — what matters more is knowing what drives the cost so you can compare quotes fairly.
The things that move the price:
When you collect quotes, make sure each one spells these out. A quote that's just a single rate with no scope is impossible to compare against one that itemises preparation, exposure, stone, sealing and repairs. Comparing like with like is the whole game.
- Area and access — size, and how easily machinery and materials reach the site.
- Exposure method — retarder/wash, seeding or a ground finish all differ in labour.
- Stone type and size — decorative stone choices vary.
- Surface preparation and base — ground conditions, drainage and any demolition of an old surface.
- Sealing — the sealer chosen and whether an anti-slip additive is included.
- Repairs — if you're working with an existing slab, its condition.
What to ask your installer
A few good questions separate a considered quote from a vague one:
Good installers welcome these questions. The answers tell you as much about how they work as the quote does.
- Which exposure method will you use, and why that one for my site?
- What stone size and colour are you proposing — can I see representative samples?
- What exposure depth are you aiming for, and how will you judge the wash timing?
- What sealer will you use, and will it include an anti-slip additive for wet or sloped areas?
- Will you lay a sample or test panel before committing to the full area?
- Have you assessed the slab, site and drainage, and does my soil type change anything?
- If grinding is involved, how will silica dust be controlled under a site control plan?
This guide supports project planning. Confirm the selected products, substrate requirements and installation instructions with the supplier.
